ISTAGRAM: cody3d1 https://www.instagram.com/cody3d1/
The Space Launch System (SLS): NASA’s Artemis 1 Moon Rocket take off (lamp) and pedestal. Model Printing Miniature Assembly File STL-OBJ for 3D Printing FDM-FFF DLP-SLA-SLS
Two size 1:18 for FDM-FFF, 1:37 for DLP-SLA-SLS,
more than 200 hours of modeling
however, the dimensions can be changed with each slicer
in total The Space Launch Systemis is composed of 11 mil points
all the files have been decimated by the polygons, but without losing the details, this makes the light files suitable for each computer
dimensions take off FDM-FFF W 20,7Cm D 15Cm H 59Cm
W 8,1Inch D 5,9inch H 23inch
dimensions pedestal FDM-FFF W 11,6Cm D 7,5Cm H 49Cm
W 4,5Inch D 2,9inch H 19inch
dimensions take off DLP-SLA-SLS W 11,6Cm D 8,5Cm H 33Cm
W 4,5inch D 3,3inch H 12,9inch
dimensions pedestal DLP-SLA-SLS W 6,5Cm D 4,2Cm H 27Cm
W 2,5inch D 1,6inch H 10,6inch
all files are already in place for optimal printing
The Space Launch System 3D model was designed to get a clean print result, without considering printing material consumption, However, you are free to rotate, or scale,
every part of the model in the most convenient way for you.
Each file has been checked and repaired with Netfabb
The parts of the model are already positioned for 3D printing
Compatible with every Slicer- Simplify3D, Care, Slic3r, etc ...
All the parts of the model have been cut so as to be printed vertically, for a higher quality of printing
Artemis 1, officially Artemis I, is a planned uncrewed Moon-orbiting mission, the first spaceflight in NASA's Artemis program, and the first flight of the agency's Space Launch System (SLS) rocket and the complete Orion spacecraft.[note 1] NASA is currently targeting a launch window starting from 14 November 2022.
Formerly known as Exploration Mission-1 (EM-1), the mission was renamed following the creation of the Artemis program. The mission will lift off from Launch Complex 39B at the Kennedy Space Center aboard the Space Launch System rocket. The Orion spacecraft will be launched on a mission of between 26 and 42 days, with at least six of those days in a distant retrograde orbit around the Moon. After reaching orbit and performing a trans-lunar injection (burn to the Moon), the mission will deploy ten CubeSat satellites and the Orion spacecraft will enter a distant retrograde orbit for six days. The Orion spacecraft will then return and reenter the Earth's atmosphere, protected by its heat shield, and splash down in the Pacific Ocean. The mission will certify Orion and the Space Launch System for crewed flights beginning with Artemis 2. After the Artemis 1 mission, Artemis 2 will perform a crewed lunar flyby and Artemis 3 will perform a crewed lunar landing, five decades after the last Apollo mission.
The Orion spacecraft for Artemis 1 was stacked on 20 October 2021, marking the first time a super-heavy-lift vehicle has been stacked inside NASA's Vehicle Assembly Building (VAB) since the final Saturn V. On 17 August 2022, the fully stacked vehicle was rolled out for launch, after a series of delays caused by difficulties in pre-flight testing. The first launch attempt was made on 29 August 2022, but was cancelled due to a faulty reading on a redundant sensor. The second attempt on 3 September 2022 was also cancelled after a hydrogen leak was discovered. On the same day, in order to focus on troubleshooting the SLS, NASA decided to forgo any launch attempts in the launch window ending 6 September. After the leak was satisfactorily repaired, the next launch opportunity was initially on 27 September 2022 before trajectory forecasts for then-Tropical Storm Ian led to a weather delay. After the weather cleared out, NASA chose 14 November 2022 as the launch date for the Artemis 1 mission.
Recommended settings for printing
each part was cut to be printed vertically, to have a better quality print, so for the upper parts,
it is recommended to print with a 4-5 skirt
Layer height: 0.1mm*
Initial layer thickness: 0.3mm
Bottom/top pattern: lines
Horizontal expansion: 0.04mm (when entering 0.04mm index, the 3D printer perceives the model as monolith, i.e. as having no hidden layers).
*Layer Height 0.1mm is recommended for a better quality for the printed model. However, the printing time will double.
As a STL file provider, our goal is to ensure that the files are error-free and printable in the most accurate way. This is why we only test print the most difficult segments of
the model’s parts.
The model's parts have been tested and printed in PLA. In case you need advice where to get your filaments from, check our partner's website.
Infill speed: 30mm/s
Outer shell speed : 30mm/s
Inner shell speed: 20mm/s
Top/bottom speed: 20mm/s
Support speed: 50mm/s
Travel speed: 150mm/s
Skirt speed: 30mm/s
Amount of slower layers: 4
Infill pattern: Grid
Line distance: 1.5mm
Infill overlap: 20%
Infill layers: 0
Enable support: Check
Overhang angle: 30°
X/Y distance: 0.7mm
Top distance: 0.2mm
Bottom distance: 0.2mm
Stair step height: 0.5mm
Join distance: 0.7mm
Area smoothing: 0.6mm
Use towers: check
Line distance: 1.5mm
Any act to promote or gain profit in any manner (e.g. either monetarily or socially) from the use of my profile, video, pictures or audio in any form my profile is a violation
of my privacy and subject to legal action. BY WATCHING THIS: You acknowledge and agree that you shall not post, upload, publish, transmit or make available in any way content of this
page including images and recording streamed live video available for download. This is intended as, and presented as a one time, live, one view presentation only.
Penalties of Copyright Infringement: By reproducing, republishing or redistributing the work of a copyright holder without permission, you may be violating or infringing
on his or her rights under the Copyright Act. The copyright holder may sue for compensation cost from $ 250 to $ 150,000 or one year jail sentence